Mending pipes - plumbing in general

also made. The ends may be machined for butt welding, threaded (usually female), or socketed, etc. When the two ends differ in size, the fitting is called a reducing elbow or reducer elbow. Elbows are categorized based on vari

Mending pipes - plumbing in general plumbing London

Wikipedia about elbow pipes

An elbow is a pipe fitting installed between two lengths of pipe or tubing to allow a change of direction, usually a 90° or 45° angle, though 22.5° elbows are also made. The ends may be machined for butt welding, threaded (usually female), or socketed, etc. When the two ends differ in size, the fitting is called a reducing elbow or reducer elbow.

Elbows are categorized based on various design features as below:

Long Radius (LR) Elbows ? radius is 1.5 times the pipe diameter
Short Radius (SR) Elbows ? radius is 1.0 times the pipe diameter
90 Degree Elbow ? where change in direction required is 90°
60 Degree Elbow ? where change in direction required is 60°
45 Degree Elbow ? where change in direction required is 45°

A 90 degree elbow is also called a "90 bend" or "90 ell". It is a fitting which is bent in such a way to produce 90 degree change in the direction of flow in the pipe. It is used to change the direction in piping and is also sometimes called a "quarter bend". A 90 degree elbow attaches readily to plastic, copper, cast iron, steel and lead. It can also attach to rubber with stainless steel clamps. It is available in many materials like silicone, rubber compounds, galvanized steel, etc. The main application of an elbow (90 degree) is to connect hoses to valves, water pressure pumps, and deck drains. These elbows can be made from tough nylon material or NPT thread.

Źródło: https://en.wikipedia.org/wiki/Piping_and_plumbing_fitting


Some facts about history of water supplies

As recently as the late 19th century sewerage systems in some parts of the rapidly industrializing United Kingdom were so inadequate that water-borne diseases such as cholera and typhoid remained a risk.

From as early as 1535 there were efforts to stop polluting the River Thames in London. Beginning with an Act passed that year that was to prohibit the dumping of excrement into the river. Leading up to the Industrial Revolution the River Thames was identified as being thick and black due to sewage, and it was even said that the river ?smells like death.?24 As Britain was the first country to industrialize, it was also the first to experience the disastrous consequences of major urbanisation and was the first to construct a modern sewerage system to mitigate the resultant unsanitary conditions.citation needed During the early 19th century, the River Thames was effectively an open sewer, leading to frequent outbreaks of cholera epidemics. Proposals to modernise the sewerage system had been made during 1856, but were neglected due to lack of funds. However, after the Great Stink of 1858, Parliament realised the urgency of the problem and resolved to create a modern sewerage system.

Źródło: https://en.wikipedia.org/wiki/History_of_water_supply_and_sanitation


Plumbing - what a valve is?

A valve is a device that regulates, directs or controls the flow of a fluid (gases, liquids, fluidized solids, or slurries) by opening, closing, or partially obstructing various passageways. Valves are technically fittings, but are usually discussed as a separate category. In an open valve, fluid flows in a direction from higher pressure to lower pressure. The word is derived from the Latin valva, the moving part of a door, in turn from volvere, to turn, roll.

The simplest, and very ancient, valve is simply a freely hinged flap which drops to obstruct fluid (gas or liquid) flow in one direction, but is pushed open by flow in the opposite direction. This is called a check valve, as it prevents or "checks" the flow in one direction. Modern control valves may regulate pressure or flow downstream and operate on sophisticated automation systems.


Źródło: https://en.wikipedia.org/wiki/Valve